Category: Farmhouse

Fall DIY Blog Hop

Published on by Danya | A Vintage Flare Farmhouse10 Comments

Wow!! Happy September! How is it September y’all? Seems like the summer ran right past me!

I love fall decor, but I’m so sad to see summer come to an end (it’s my fave if you can’t tell).

Welcome to our Blog Hop Hosted by my sweet friend Terrie at Decorate and More with Tip.

In honor of all things pumpkin we will each be bringing you a Fall DIY! Don’t forget to scroll to the bottom and check out all of my sweet friends fall projects!

If your coming here from Pretty DIY Home, welcome and thanks for stopping by 🥰

Honestly, my pumpkins and pretty fall decorations are still in the attic.

What about y’all? Have y’all broke out your pumpkins? I think this weekend I’m going to start my fall decorating.

For my Fall DIY, I’m going to show y’all 3 easy projects. One of them is fall-ish!

Fall Banner

I love simple banners and am going to make a vintage one using tea stained paper.

Items Needed:

  • Card stock
  • Printer
  • Scissors
  • Clothes pins
  • Jute rope
  • Tea bags
  • Oven

I started by searching the internet for some simple fall images.

I searched for black and white sunflowers and hydrangeas. Once I found the images that I liked, I printed 2 of each. Prior to printing I changed my settings to 2 on each page so they would be the size I wanted.

I would recommend printing them on regular paper first, to ensure they are the right layout. I then went to word and created the word FALL in word art and then printed this as well. If I do this again I’ll make my letters pop more.

After I printed out what I wanted on my banner, I then cut everything to the appropriate size.

Now it’s time to tea stain the paper. Steep your tea as usual (boil water, add bags, cover). I used a container wide enough to fit my paper for steeping the tea. I then added my paper and opened up one of the bags and sprinkled the tea on each sheet. Be sure all of the sheets get saturated.

After each page was saturated with the tea I hung them up so the excess water would drip off. I only did this for about three or four minutes. Now set your oven for 375. Lay each sheet of paper on a cookie sheet and bake for around 5 to 10 minutes. Be sure to keep a good eye on them. Once the paper is dry then the process is complete.

Now measure where you want your banner to hang and cut your jute rope.

Clip each banner piece to the rope using your clothes pins.



Hydrangea Wreath

This was not my favorite project. What I envisioned was so much prettier than my outcome. Lol. I ended up taking it apart and redoing it.

My limelite hydrangea shrubs have been overflowing with hydrangeas! Now that I have the drying process down I decided to try my hangs at a wreath using them.

Items Needed:

  • Grapevine wreath
  • Floral wire
  • Glue gun
  • Dried Hydrangeas
  • Something to lay this on to catch the huge mess your about to make 🤣
  • Scissors
  • Floral filler

The amount of hydrangea you will need depends on the fullness you want on your wreath and if you want to fill the entire wreath or just one side of it. I think after I made the first one I realized I prefer wreaths with only one side full of flowers.

I always start by laying out how I want my wreath to look. Then move everything off the wreath and add your floral wire about 3-4 inches apart. Lay several stems on the wreath and twist the wire tight. Continue until you have it all filled in. I then use my glue gun and lift some of the flowers and glue them down.

Not the best picture, but even after I took the sunflowers out I didn’t like it.

I then took everything off of one side, added more hydrangeas, a few red flowers, the “hey y’all” wood words, and then a bow.

I’m still not sure I LOVE it, but it was super inexpensive so it will do for now.

Now, I need more hydrangeas to dry out so I can make a second one and get them on our double doors.

Olive Branch Topiary

I’m going to give you the basics for this, but for full instructions on the topiary click HERE and for full instructions on aging your terra cotta pots click HERE.

Items needed:

  • Terra cotta pots
  • 2 Olive branch stems 26″ per pot
  • Styrofoam Foam ball
  • Tacky glue
  • Moss
  • Kabob stick
  • Twine

Glue the ball down in the bottom of the pot. Stick the olive branch stems and the kabob stick into the center of the ball. I took mine back out and added glue to the hole and then placed them back in. Tie the kabob stick to the olive branch stems. Then add moss to the top or the pot.

THANKS SO MUCH FOR STOPPING BY!! DON’T FORGET TO SCROLL ALL THE WAY DOWN AND CHECK OUT EVERYONE’S AWESOME Projects!

If you decide to give this a try, tag me on IG or FB so I can share! Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 

❤️❤️Danya

Decorate and More with Tip

Corbel Peg Rail Shelf

Published on by Danya | A Vintage Flare FarmhouseLeave a comment

Hello friends!

If you had a chance to check out my recent peg rail post then you know I had plans to add to it. When I purchased the wood for the peg rail shelf I bought the wrong size wood!! Instead of delaying the rail we went ahead and built the rail and then added the shelf.

I love how it turned out and want them all over the house now. Lol.

SHOP MY HOME HERE

Here are the instructions for the peg rail shelf. My photos may vary a bit from the instructions since my project was a bit different.

Items needed:

  • 1 x 6 8 ft common pine
  • 1 x 4 8 for common pine (I accidentally bought a 1 x 3 so now I have 2- 1 x 3’s under the shelf)
  • 1″ dowel rod 6 ft
  • Corbels (I found a 2 pack for $25 HERE)
  • Miter saw
  • Sand paper / pad 120 grt
  • Nail gun
  • Wood glue
  • Caulk
  • Paint and paint brush
  • Drill and 1″ paddle bit
  • Pencil
  • Tape measure

Cuts

    Dowel rod, 17- 4″ pieces for pegs
    1 x 4- 7′
    1 x 6- 7′ 3″

RAIL

Cut 17 pegs 4″ in length. This should give you a spacing of 5″ apart.

First you need to mark your board and use the paddle bit to make your peg holes.

Take your 1 x 4 and mark the center of the board at 42″. I went 1 1/2″ from the top. Using your pencil mark at 42″ and 1 1/2″ down and then go left and right of center marking 5″ apart. You should end up with 17 marks.

Use your paddle bit and drill your peg holes.

You will now need to lightly sand your pegs and peg holes.

Using your wood glue add your pegs to each hole (we ended up not using glue for this because the fit was tight and the paint helped hold them in place).

PAINT

Go ahead and paint everything before you start putting it together. Or you can do it after it’s hanging BUT I’m super messy and this would be a disaster 😭!

SHELF

You can either attach your shelf to the peg rail now or hang your rail and attach the shelf to it while hanging (I honestly think it easier to hang the rail first).

Mark the center of your 1 x 6 and the center of your rail.

Using your nail gun attach the shelf to the rail.

HANG

We used the nail gun and hung the peg rail shelf and then added the corbels to each side and nailed them in place.

I then used my white caulk and caulked any gaps and then touched up my paint.

There you go! You now have a beautiful corbel peg rail shelf for less than $40.

Ignore my daughter making a Tik Tok 🤣🤣

Thanks so much for stopping by!!

If you decide to give this a try, tag me on IG or FB so I can share! Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

❤️Danya

Monthly Blog Hop- Dowel Rod

Published on by Danya | A Vintage Flare Farmhouse14 Comments

Happy August Everyone!!!

Where did summer go? I have no clue how it’s almost over. Anyone else feel like this? As much as I love fall decor…. I’m not ready to give up on summer just yet! What about y’all?

Who’s on the I’m sticking with summer until the end team and who’s team fall? I have a feeling I’ll be on the losing team with team summer 🤣!

➡️➡️Welcome to our Blog Hop Hosted by my sweet friend Terrie at Decorate and More with Tip.

⚠️Don’t forget to scroll to the end of this post and check out all of my amazing blogging friends projects!TO SHOP MY HOME and for great Fashion deals follow me HERE!!

For my project I set out to make a peg rail shelf for my shiplap wall. I accidentally picked up the wrong size wood for the rail 💁🏻‍♀️, so I ended up just making a peg rail. I still love it and it was very easy to make, BUT I’ll for sure be adding an additional piece of wood and shelf to it soon. 

Save now, read later!!!!

Items Need:

  • 1” dowel rod 6ft long (the length you need with be determination by how many pegs you are adding)
  • 1×3 8ft board
  • Wood glue
  • Sand paper ~120’grit
  • Nail gun with finishing nails (or hammer and nails if your don’t have a nail gun)
  • Drill
  • 1” Paddle bit for drill (to make 1” holes on rail)
  • Paint
  • Pencil
  • Tape measure

Cuts:

  • Dowel rod 17- 4” pegs (for 5” apart spacing)
  • 1×3 7’

First

Make all of you cuts as listed above. For my peg rail I’m using a 1” dowel rod and cut 4” pegs that will be 5” apart.

I used the miter saw to make the cuts, but be really careful since they are short cuts and they tend to roll while you are trying to cut! We don’t need anyone losing a finger!!!

Next

Use your sand paper or sanding pad and sand your board and pegs

Next

Find center of peg of your board. Mine is 84” long so center is 42” (I like simple number and none of that… 3 lines past 42 🤣)Mark the center of your board at 42” and 1 1/2” down.

I didn’t center my pegs in the middle of the board just in case I want to come back in later and add a small shelf above my rail.Once you find the middle of your board go left of center and then right of center marking all of your spots where the pegs will go.

Next

Use your paddle bit and drill and make all of the holes on your board for your pegs using your marks.Sand the edges of each hole.Add your pegs to each hole. You can use your wood glue for this. We actually didn’t use any glue because they fit pretty tight and don’t have plans to have anything heavy on the pegs. Also, your paint will help hold them in place.Now paint you board and pegs.

Last

Hang your peg rail. We used our nail gun for this but you could just use a hammer and nails.>>>> If you want to add a shelf over your peg rail (which I plan to do soon) instead of a 1×3 board for the rail use a 1 x 4 and then for your shelf use a 1×6 cut at 7’1″ (overhang 1/2” on each end).Isn’t it super cute? And it was so easy!!!

Don’t forget to keep scrolling for more inspiration!

Thanks so much for stopping by!!

If you decide to give this a try, tag me on IG or FB so I can share!Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

❤️Danya

terrarium
Decorate and More with Tip
white DIY plate rack with blue and white plates
Pallet and Pantry
DIY miniature tree
Blessings by Me
closeup of jute rope tied onto end of dowel rod
B4 and Afters
DIY sailboat
The House House
monogram wall letter made out of dowel rods
Patina and Paint
rope wall art
Celebrate and Decorate
roller cart with plants on it
A Vintage Flair Farmhouse

Blog Hop- Christmas in July

Published on by Danya | A Vintage Flare Farmhouse16 Comments

Hello everyone!

Can you believe July is almost over?

Time has been flying by for me!

Welcome to our Blog Hop Hosted by my sweet friend Terrie at Decorate and More with Tip.

Our theme this month is Christmas in July. We were each challenge to make something related to Christmas!

I don’t know about y’all, but it’s hard to think about Christmas when it feels like 150° outside!

We were hanging shiplap in our bedroom so this seemed like the perfect time to make a shiplap Christmas tree box.

⚠️Don’t forget to scroll to the end of this post and check out all of my amazing blogging friends projects!

If you are coming here from B4 and Afters page, thank you! I can’t wait to head over and check out her Christmas in July blog post! Did y’all see her adorable pine cone trees? Super cute!

Anywhoo… let’s get our the power tools and see what I can mess up 😂!

BTW for my favorite power tool and other finds click HERE! There is a great deal right now for a drill and impact for $99! Sayyyyyy what!

Items used:

  • Nail gun with finishing nails
  • Tape measure
  • Square
  • Pencil
  • 2- 2×2 8ft each (we used pine left over from making our farmhouse table)
  • 2- 8 ft pieces of Shiplap (we used left over tongue and groove OR you can have the hardware store rip plywood for you).
  • Laser jet printer

Cuts:

2×2’s

  • 4- 18″
  • 4- 19 1/8″
  • 4- 9 3/4

Shiplap (ours is 6″ wide)

  • Measure your box once done and make your cuts from that.

Cost:

Zero for us since everything was left over from other projects.

FIRST

Measure your tree stand to make sure your box will easily fit around your tree. Our stand is 23″ x 23″.

If your tree measures the same then follow the cuts listed above for your lumber.

NEXT

Now that you have all of your cuts start with the pine.

You’re going to make two Squares and then use the shorter pieces between the two  squares to make a box. This is how you will attach the shiplap.

Use the longer pieces on the top and bottom and the shorter pieces on each side. Also don’t forget to use your square to make sure it’s all straight.

Now listen… I’m a girl and don’t speak in lumber language so be nice and don’t be too judge-E of my instructions!

And while we’re on the subject.. why do they call a triangle a square? I know it’s used to keep things square, BUT ITS A TRIANGLE!

Nail these pieces together.

Repeat the same process and make a second square.

NEXT

Using your 9 3/4″ pieces use them between each square in each corner making a box.

NEXT

Now it’s time to attach your shiplap. We had to rip 4 of these pieces with the table saw to get it to fit right.

LAST

Now it’s time to add your words. This is the first time I have done this process and I for sure would have went larger!

Also be sure you have a laser printer.

I used word and wrote our what I want it to say. Then when I went to print it I reversed everything. For me it was tricky finding this setting. It’s under your print options and there is a box that says reverse.

Print and then lay it out on your wood. You can use an u sharpened pencil for this, but I used a paint can opener and this worked good.

Just go back and forth over each word and your ink will transfer to your wood.

I had a little mess up with it at first and had to start over so mine is a little messy 🤦🏻‍♀️.

Don’t forget to keep scrolling and for more Christmas in July inspiration!

Thanks so much for stopping by!!

If you decide to give this a try, tag me on IG or FB so I can share!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Decorate and More with Tip | Sew Sassy by Paula | DIY Vibes | Pretty DIY Home

Bluesky at Home | Patina and Paint | Celebrate and Decorate | B4 and Afters

A Vintage Flare Farmhouse | LeCultivateur | Country Road 407 | The House House\

Jessica B Simmons | Living Little John

 

Farmhouse Outdoor Table and Benches

Published on by Danya | A Vintage Flare Farmhouse18 Comments

Farmhouse Outdoor Table and Benches

Hey, hey everyone! We have had an iron outdoor patio set for many years, which is super sturdy and great, but REALLY doesn’t match my style!

PSSST for my fave paint brush CLICK HERE

Welcome to our monthly blog hop hosted by my friend Terrie at Decorate and More by Tip!

This month we are each doing a DIY on something for Summer! This seemed like the perfect opportunity to upgrade out patio table. Be sure to scroll all the way to the bottom and check out everyone else’s fun summer DIY’s!

If your coming over from Liberty’s blog b4 and afters, welcome 🙂

 

Old Table

I saw what looked like an easy DIY on Ana White’s blog. If you love DIY wood working projects you seriously need to check her out! Click Here to see her plans that I followed.

I set out to try this project on my own, but Mr. A Vintage Flare Farmhouse was feeling extra sweet and assisted. OKAY, OKAY I assisted him! But, the point is he did it so I cant take credit, lol! He made it look super easy and did the table and 2 benches from start to finish in 2-3 hours!

Supplies Needed for Table and 2 Benches:

  • 2×4
    • 12, 8 ft long boards (6 are for the benches)
    • 2×6
  • 6, 8 ft long boards
    • 2, 12 ft long boards to be cut in 1/2 (these are for the benches, or 4 more 8 ft long and you will have to cut them down to 6ft)
  • Self tapping wood screws
  • Tape Measure
  • Miter Saw
  • Optional Nail Gun (we used this and then went back with the screws)
  • Palm sander (click here for my fave)
  • Stain of choice. I used medium walnut Danish oil
  • Cloth to apply stain / oil

Cuts to be made

Table Cut List
  • 8 – 2×4 @ 28-1/2″ – end leg sets
  • 2 – 2×4 @ 75-1/2″ – side aprons
  • 1 – 2×4 @ 80″ – bottom stretcher
  • 2 – 2×4 @ 25-1/2″ (middle support)
  • 6 – 2×6 @ 92-5/8″ (tabletop boards)
Bench Cut List
  • 2 – 2×4 @ 66″ – long aprons
  • 4 – 2×4 @ 16-1/2″ – legs
  • 4 – 2×4 @ 7-1/2″ – end aprons and stretcher
  • 1 – 2×4 @ 4-1/2″ – middle

Here We Go…

>>The steps for the benches are very similar to the steps for the table.

Click on the link at the bottom of this post for more detailed information on the cuts used for each step.

Before you start reading…..

YES, I know my pics are for the benches, but its the same steps as for the table.

I was busy being a helper for the table and didn’t get pics, sorry 🤦🏻‍♀️!!

Cuts to be used for each step ARE FOR THE TABLE (even though pics are the bench)!

https://pin.it/6Egv95S

First, you will build each end of the table (Legs)

You will do this using the 2×4- 28 1/2 cuts, 4 of them. For the bottom leave 3 1/3 inches for the legs. We used wood that was left over to raise the middle pieces up until we got it nailed.

Now add the tables side aprons to each side from end to end.

Use 2 of your 75 1/2 cuts to attach each end. You can turn the legs upside down for this or use a helper.

Now the bottom stretcher (bottom middle from end to end) this will overhang 3/4″ on each side

Now use your 80″ for the bottom middle piece. It will overhang 3/4″ on each side

Sooooo… the benches do not have bottom stretchers therefore no pictures of this step!

You can see in the pic below the bottom stretcher and YAY it’s a pic of the table!

Next, is the middle support piece, 1 on each side of center.

For this we used 2 of the 25 1/2 pieces and placed them on each side of center. We did it this way so we could add our umbrella to the center of the table.

 

Finally, its time to attach your tabletop pieces.

These will overhang by 7 1/16 on each end. Find center and place a 6 ft 2×6 on each side of center.

 

Hubby added a hole in the middle of the table for our umbrella.

BAM! Sounds easy enough right! Now you have a farmhouse table! Click below for the detailed instructions on the 2 benches!

Now to sand and stain!

I seriously HATE sanding! Have I ever mentioned that before? Use your palm sander and lightly sand your table and benches. I sanded the seats and tabletop a little heavier that the rest. Lets face it… who wants a splinter in their leg or hand or worse…

I used our leaf blower and blew off the sawdust and then a damp cloth and wiped it down good.

After this dries stain and seal!

 

 

Now listen friends… Ana White is the real expert in this so check out her blog for full instructions and photos!

Ana White Beginner Farm Table

Ana White Farm Table Benches

 

Thanks so much for stopping by!!

Don’t forget to check out the OTHER PROJECTS BELOW!!!! ⬇️⬇️⬇️⬇️

If you decide to give this a try, tag me on IG or FB so I can share!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Danya

 

 

 

 

 

 

 

DECORATEANDMOREWITHTIP | PALLETANDPANTRY | CELBRATEANDDECORATE | CLOCHESANDLAVENDER

B4ANDAFTERS | AVINTAGEFLAREFARMHOUSE | BLESSINGSBYME | PAULASHANDMADESPACE

THEHOUSEHOUSE | PATINAANDPAINT | DIYVIBES | BLUESKYATHOME

Aged Terra Cotta Pots

Published on by Danya | A Vintage Flare Farmhouse4 Comments

I have seen so many gorgeous aged terra cotta pots all over Instagram and Pinterest,  I figure it’s time to give it a try.

🔥PIN NOW READ LATER🔥

I mean who has the time to let them naturally age? Wonder how long that even takes?

I have done 3 different variations of the aged pots.

The process is a bit messy (which is great since I’m super good at messy!)!

Let me know which one y’all like the best!

ITEMS USED:

  • Terra cotta pots
  • Pre-mixed concrete patch
  • Sanding pad
  • Grey or black paint
  • Baking soda
  • Clear spray on sealer
  • Gloves

CLICK HERE FOR PRODUCTS

OPTION 1

This option has the most steps, but is my favorite look!

✔️I started by spreading the concrete patch mix on the pot. This gives your pot a nice texture.

You could also use a joint compound or Spackle, but I’m not sure you would have the same texture in the end. I mainly used the concrete patch because I had some left over. 

Spread it on (wear your gloves or you may have some messy hands) and let it dry. Be sure not to leave it too globed or your going to have to work a little harder at sanding!

✔️After it dries use a piece of sand paper and smooth down your raised areas.

✔️Use some outdoor paint (grey or black or really any color you prefer) and lightly paint here and there on the pot.

Let dry

✔️Mix baking soda and water. I don’t really think that the mixing ratio is super important because the baking soda will settle at the bottom and you will use this part to spread on the pots.

I tried dipping the pot in the mixture, but it worked best when I grabbed some of the wet baking soda and rubbed it on the pot. USE GLOVES because it can burn your skin.

Let dry

After it dries use your hands and rub off any excess baking soda. It will flake right off. I also rubbed off any that ran inside of the pot.

✔️Spray with a clear sealer

OPTION 2

You will do all of the above steps, but omit the paint!

Concrete patch, dry, sand.

Baking soda, dry, wipe off

Spray with clear coat.

OPTION 3

For this look leave off the concrete patch AND the paint.

Baking soda, dry, wipe off

Spray with clear coat.

 

Which one is your fave of the 3?

 

Thanks so much for stopping by!!

If you decide to give this a try, tag me on IG or FB so I can share!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Danya

Acid Stained Concrete

Published on by Danya | A Vintage Flare FarmhouseLeave a comment

Hey guys! Thanks so much for stopping by and checking out my step by step instruction on how to DIY acid stain your concrete!

We have stained concrete inside of our home so now it’s time to add some outside! There are so many colors and options for staining your concrete! Inside we score the concrete which make it look like 12×12 stone. In another area we used a stencil and added a large R to our entryway. At some point I will do a tutorial on staining new indoor concrete. You can check out the inside of our home by clicking here🏠!

When we were building our house clumsy me spilled a brand new container of wood stain on the back porch. I was staining the wood planks on the ceiling and… Oops!!!

So right off the bat we had ugly brown blotches on the back porch. We thought about adding a stone such as skate, but staining it is the easiest and most affordable fix.

WARNING⚠️ Acid staining process will vary depending on your concrete finish, age of the concrete, and build up! If you are planning on staining your concrete using this tutorial, I would recommend testing the stain on a small hidden area first. You will also get different variations depending on the brand of stain you use. I have used different stains and have found that majority of them have the same results. Please take the time to research acid stain and watch other tutorials prior to performing.⚠️

💕You can check out the video of this process by clicking here!

Here is the porch before applying the stain.

CLEAN AND COVER

➡️Cleaning your concrete is probably one of the most important steps. Even brand new concrete it is essential to thoroughly clean it prior to applying the stain. You can rent equipment at your local hardware stores such as Home Depot or Lowe’s. For this project I am using our pressure washer with surface attachment . I first applied concrete cleaner. I then went over the patio twice with the surface attachment. This attachment is super easy to use. Then I applied concrete cleaner one last time and use the pressure washer with the nozzle attached. After that I allowed 24 hours for the concrete to dry.

You can find this surface attachment by clicking HERE

Now cover your siding or if you are working inside your baseboard and walls. You can use brown paper or plastic to do this. I used brown paper and blue painters tape.

❗️❗️A couple of important points:

  • Ensure your product is an acid stain or etching stain. NOT A PAINT
  • Ensure that your concrete is clean and dry
  • Allow 24 hours between coats
  • Do not allow anyone to walk on the area until thoroughly dry! This includes each step listed below!!! ❗️❗️

STAIN

Using your sprayer mix the stain according to specifications. Several of the stains are a 1:1 mixture of stain and water. Read your products label carefully. Using a measuring cup mix according to your product specifications.

⚠️MAKE SURE YOUR SPRAYER IS NOT SET ON STREAM and is on wide spray. If your nozzle is set on stream you will have lines of stain! Which you DO NOT WANT! Believe it or not I have seen someone do this and the end results were not good! 🤦🏻‍♀️

This is the brand I used for the porch.

➡️Evenly apply the stain using the wide spray setting. Look back over your first coat and add more stain to areas that don’t appear well covered.

Allow 24 hours to dry.

I know, I know, it looks brown and blotchy. But, this is just the color that you can see while the chemical process is occurring.

AFTER IT DRIES…. You can wet a small area to see how it will look. The color when the floor is wet is close to the color your floor will be after you have sealed it.

Water will not hurt the stain because the acid is soaking into the concrete and chemically reacting with it, but do not use a cleaner or soap. Again READ YOUR PRODUCTS LABLE.

I wanted my stain darker so I applied a second coat.

Again…. allow 24 hours to dry.

After you have achieved the desired color then you will need to rinse the product off. Some labels will use a buffer such as baking powder to stop the chemical reaction. I used baking soda and again used the wand and pressure washer.

SEAL AND POLISH

Make sure you are happy with the color before you seal it.

Remember when the floor is wet that is close to how it will look once sealed.

Take down all of your paper before you seal it and make sure you the stain is around the edges. You can always use a sponge and apply more stain in small areas that you may have missed.

➡️Use a roller and pour out the sealer and roll it.

Allow 24 hours to dry.

➡️Now for polish… the polish will give your floor the wet look if that’s what you are wanting. This is also the step that makes the floor a little slick! This step IS NOT REQUIRED, but it’s my fave! You can apply 2-3 coats until the desired look is achieved.

Read the manufacturers label on your product for full instructions. You simply mop the polish on and allow up to 4 hours to dry between coats.

There are several steps to this process, but overall it’s easy. To keep the wet look, you will need to apply the polish around every 3-6 months depending on traffic.

Again thanks so much for stopping by!!

Tag me on your project on IG or FB so I can share!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Danya



Dresser Makeover

Published on by Danya | A Vintage Flare Farmhouse19 Comments

Quarantine Upcycle Challenge: Dresser Makeover

Hello friends! Welcome to our monthly blog hop hosted by Emily at Le Cultivateur and Tara at stilettos and shiplap .

This month we will each show you something we have given a makeover. We each took something we already had (pre-quarantine) and are giving it a new look.

Don’t forget to scroll to the bottom and check out everyone else’s projects!

This month I am showing you a simple furniture redo. Well simple for me since my projects are typically a disaster 😂😂. You can see what I mean by checking out my shelf redo and my Buffett mess.

Here is a before shot of the dresser that I found on marketplace for $35 back before COVID hit. I am redoing my grandsons room and needed a place to store his clothes and a few of his toys.

I honestly search marketplace several times a week, but I typically miss the good stuff. This one was listed with my Buffett so I was able to get both pieces for $70!

If you can find real wood pieces for those prices that’s a great buy in my book!

We also found him a daybed on amazon that is super affordable (I’ll show y’all the final room once we get a mattress and bedding).



You can check out the bed here.

SANDING

The thing I usually hate most is sanding. First I remove all of the hardware and clean the furniture with either diluted bleach or a soapy rag.

I knew my plan for the dresser was to use chalk paint so thank God there wasn’t much sanding to do! I just lightly sanded any rough spots and corners.

Here is a link to my favorite sander! It’s a palm sander and is so easy to use (and is less that $60 🙌🏽). You can also find the chalk paint that I used by clicking HERE. Chalk paint is by far the easiest paint to use in my none expert opinion! It will cover almost anything.

CRACKLE / CHIPPY

After I lightly sanded the dresser and cleaned it I applied a coat of crackle glaze. This is what gives this piece the chippy look without sanded or working hard for it (remember I hate sanding!).

I applied a coat to the entire piece and then let it set for around 45 min. You want the glaze to have a tacky feeling to it before you apply your paint.

PAINT

Now that my glaze has a tacky feel I applied one coat of my fave chalk paint.

THATS IT! I have been amazed with this glaze. Usually it’s pretty difficult to get that chippy look. But with this glaze it’s crazy easy!!

HARDWARE

I cleaned up the hardware and reapplied what I had. The dresser was missing 2 handles so I used some inexpensive faux crystal balls for those pieces.

All Finished!!

Can y’all guess the bedroom theme? 🤔

Thanks so much for stopping by!!!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Don’t forget to scroll down and check out everyone else’s projects!

https://throughavintagedoor.com/quarantine_upcycycle_challenge_painted_suitcase/

 

https://www.thehousehouse.com/upcycling/quarantine-upcycle-challenge

Quarantine Upcycle Challenge: Crib to Patio Bench

DIY Slat Wall: Closet Makeover

Quarantine upcycling challenge – from bunk beds to day bed

Mantle Decor

Published on by Danya | A Vintage Flare Farmhouse18 Comments

Mantle Decor

Hello everyone and welcome to our blog hop hosted by Terrie at Decorate and More with Tip.

Don’t forget to scroll to the end of this post and check out all of my amazing blogging friends and se how they styled their mantles!

fireplace 5

This month everyone is sharing how they decorate their fireplaces and mantles. I figured this would be the perfect opportunity to share with y’all how you can transform your TV into any piece of art that you desire.

Who else has their TV on their fireplace mantle?

I am always envious of those that are able to style their mantle without this huge black TV screen messing it up. BUT lets face it… I’m not the only one who lives in our house and occasionally my hubby wins a decorating battle.

I have a couple of tricks that I am going to share with you on how I work around the TV and still get stylish pictures.

Be sure to scroll to the bottom and check out all of the other great ideas!

If you are coming to be from Shea at Sweet Southern Blog thank you. I love Shea’s blog and all of her amazing projects and ideas. Isn’t her shiplap gorgeous?!

Click HERE to shop my home!

 

Styling Your Fireplace

How to style your fireplace?

This really depends on your fireplace and your style. If you have a beautiful all white fireplace then you are safe to fill up your hearth and mantle with lots of fun things!

Fireplace Photo Credit: Pinterest

We went with a rock fireplace to match the rock on the outside of our house. I do wish I had designed it a little better to lighten the room up more, but there’s no going back now. If I had it to do over I would keep the same rock below the mantle and have shiplap above the mantle. This would for sure lighten up our room.

Since our fireplace is more colorful and dark, I keep my décor very simple. I prefer not to take away from the beauty of our rock and I don’t want to have a cluttered look. Therefore, I will usually place a large item on each side of the fireplace, and a few taller pieces on each side of the TV, and then add a simple garland. Also, during the winter we get a lot of use out of the fireplace so we have to be careful not to place items too close to the fire.

Hiding / Styling your TV

How to keep your TV and still get that stylish picture for instagram, pinterest, facebook, etc..

There are 2 things that I have done that are super easy!

The first one is just as simple as sitting a piece of art in front of the TV. Any large art piece that is thin enough to sit on the mantle.

fireplace 4

The next way I hide my TV is by not hiding it, but using it! YEP!  I use it to my advantage.

Do you have a smart TV or an apple TV? Those are the only products I am familiar with, but I am sure there are a ton of other devices you can use.

I will either use my apple TV and go to YouTube and type in what I am looking for such as “Spring Scene” or “Winter Scene”. Then you have a gorgeous picture right there to complement you own photo.

fireplace 6

You can also mirror your phone a screen. With an iPhone swipe up on the bottom of your screen. The same place you would go to for your brightness, airplane mode, etc… There is a button there that says screen mirror and then I just choose apple TV. Then I can mirror whatever I see on my phone to the TV. Now with some photos you may have to pinch in on your photo to get the picture where you want it.

Now for this you will have to use another phone to take your stylish picture because your phone is mirrored to the TV. Easy enough, borrow hubbies….. if he wants to keep the TV, Right?

 

Thank you so much for stopping by!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

Danya

           

LITTLE BUT MIGHTY REDO

Published on by Danya | A Vintage Flare Farmhouse4 Comments

Little But Mighty Cabinet Redo

This little shelf may seem little, but man it was a HUGE redo!

Do y’all ever have those projects? You start out thinking oh this is going to be an easy breezy redo…. NOPE!

This little shelf was given to us years ago and was in our daughters room for YEARS.

She has had layer after layer after layer of paint! Eventually she lived in our garage and was used for shoes.

Recently we added 2 “shoes shelves” to the garage and I thought this would be the perfect shelf for my grandson to use in his room here.

Well… over a week later she is finished. I’m still not in love with the end result, but it will be perfect for storing his books.

Here we go…

Items used (it’s a lot🤦🏻‍♀️):

  1. Stripper
  2. Plastic wrap
  3. Scrapper
  4. Mineral spirits
  5. Spray bottle with 1/2 water and 1/2 bleach
  6. Sander
  7. Old rags
  8. Stain of choice
  9. Crackle glaze
  10. Paint of choice
  11. Paint brush
  12. Antique wax
  13. Sealer
  14. Glue gun or wood glue
  15. Book pages

 

Click HERE for the products

Stripper

I first started the stripping process. The first stripper I use was good for nothing EXCEPT burning my skin with the splatters from it. I then switched strippers and covered it with plastic wrap. After doing this 3 times and leaving it for 24 hours each time this was SO MUCH EASIER!

Apply stripper, cover with plastic wrap, leave 24 hours. Remove wrap and use your scrapper to loosen paint. Once you loosen up the paint by scrapping repeat the process. Now repeat the process one last time.

Now wipe the cabinet down with mineral spirits using an old rag/cloth.

(Don’t use the stripper in this picture!!)

Click HERE for the stripper to use!

Sand

I use a palm sander and love it. I used a higher grit (80) for this project.

Just smooth the wood edges and remove any left over paint with the sander.

Once I’ve finished sanding I sprayed the entire piece down with bleach water and left it for a couple hours. I then sprayed it again and gave it a good wipe down.

Stain

I used 2 different stains and honestly I didn’t need to do this. I was thinking the different stain colors would show through the crackles but it really didn’t. I am starting on a new project today using the same crackle product and for this one I’m only using a dark stain all over.

Basically whatever staining process you want to use.. go for it. You will only see peeks of the stain come through the crackled paint.

Crackle

Apply the crackle product all over using a paint brush and going the same direction with each stroke.

Let this sit for around 45 minutes (until it’s tacky).

Paint

After your crackle is tacky now you can paint. Apply the paint the same direction as you applied the crackle glaze.

This product is pretty awesome. You can see the crackle almost immediately.

Click HERE for products used.

Except for the glaze…. click HERE for the GLAZE!

Book Pages

This was a bit of a disaster 🤣! Basically to make a SUPER LONG process short… I first used mod podge and applied the book pages… HATED IT… attempted for 3 days to remove the pages. Finally gave up and used my glue gun and added different book pages.

My best advise for this is NEVER use mod podge and book pages unless you are sure that’s what you want 🤣🤣!

⬆️⬆️HATED THIS ⬆️⬆️

Antiquing wax

Apply the wax with a dry cloth working it into the cracked and then wipe off with wet cloth.

Overall I will for sure be using the crackle product again and I may venture into lining a shelf with book pages in the future, but I will make 110% sure it’s what I want! Also finding the right stripper will speed future products up tremendously!

Thanks so much for stopping by!!!

Be sure to give me a follow here and on Instagram, Facebook, and Pinterest for more projects 😘.

 

https://pin.it/5grkFQ6